Welcome, in this video we will guide you through the conversion from packing to an O-Pro® Barrier seal in Viking pumps with the U-Plus™ bracket. This video applies to these pump models…

Before you begin, please consult the appropriate technical service manual for safety information. A copy of the latest revision can be found on our website at vikingpump.com.

To begin, bend up the tang of the lock washer.

Welcome, in this video we will guide you through the replacement of O-Pro® Barrier seal o-rings in Viking pumps with the U-Plus™ bracket. This video applies to these pump models…
Before you begin, please consult the appropriate technical service manual for safety information. A copy of the latest revision can be found on our website at vikingpump.com.
To begin, bend up the tang of the lock washer.
Place a brass or hardwood bar into the port opening to keep the pump from turning.
Loosen and remove the locknut. Remove and discard the lock washer.

Welcome, in this video we will guide you through the conversion from a stuffing box mechanical seal to a behind the rotor seal in Viking pumps with U-Plus™ bracket. This video applies to these pump models…

Before you begin, please consult the appropriate technical service manual for safety information. A copy of the latest revision can be found on our website at vikingpump.com.

To begin, remove the stainless-steel window guards from the bracket.

Before you begin, please consult the appropriate technical service manual for safety information. A copy of the latest revision can be found on our website at vikingpump.com. To begin, bend up the tang of the lock washer. Place a brass or hardwood bar into the port opening to keep the pump from turning. Loosen and remove the locknut. Remove and discard the lock washer. Loosen the bearing housing set screws. Loosen and remove the bearing housing. Remove the bearing spacer collar. The collar may have come out the bearing housing. Remove the half round rings.

Welcome, in this video we will guide you through the replacement of packing in Viking pumps with the U-Plus™ bracket. This video applies to these pump models… Before you begin, please consult the appropriate technical service manual for safety information. A copy of the latest revision can be found on our website at vikingpump.com. To begin, remove the stainless steel window guards from the bracket. Next, bend up the tang of the lock washer. Place a brass or hardwood bar into the port opening to keep the pump from turning. Loosen and remove the locknut. Remove and discard the lock washer.

To begin, securely clamp the pump to the bench or work surface to keep the pump from tipping. Next, remove the head cap screws. Remove the head. Tip the head back to keep the idler pin from falling off the idler pin. Remove the idler. Discard the head gaskets. Note the number and thickness of the gaskets as these will need to be replaced. Loosen and remove the bearing plate cap screws and remove the bearing plate. Next, insert a brass or hardwood bar into the port opening to keep the pump from turning. Using a bearing locknut tool or spanner wrench, loosen and remove the locknut.

Welcome!  In this video we will guide you through the disassembly and reassembly of Viking Pump’s 893, 895, and 897 Series™ mag drive internal gear pumps.

This video applies to these pump models: GG893, HJ893, HL893, AS893, AK893, AL893, GG895, HJ895, HL895, AS895, AK895, AL895, GG897, HJ897, HL897, AS897, AK897, AL897

Welcome, in this video we will guide you through the conversion from packing to Viking Pump’s O-Pro® Cartridge seal in pumps with the U-Plus™ bracket. This video applies to these pump models… Before you begin, please consult the appropriate technical service manual for safety information. A copy of the latest revision can be found on our website at vikingpump.com. To begin, remove the stainless-steel window guards from the bracket. Next, bend up the tang of the lock washer. Place a brass or hardwood bar into the port opening to keep the pump from turning. Loosen and remove the locknut.

Welcome, in this video we will guide you through the replacement of o-rings in an O-Pro® Cartridge seal for pumps with the U-Plus™ bracket. This video applies to these pump models… Before you begin, please consult the appropriate technical service manual for safety information. A copy of the latest revision can be found on our website at vikingpump.com. To begin, bend up the tang of the lock washer. Place a brass or hardwood bar into the port opening to keep the pump from turning. Loosen and remove the locknut. Remove and discard the lock washer. Loosen the bearing housing set screws.

To begin, bend up the tang of the lock washer. Place a brass or hardwood bar into the port opening to keep the pump from turning. Loosen and remove the locknut. Remove and discard the lock washer. Loosen the bearing housing set screws. Loosen and remove the bearing housing. Remove the bearing spacer collar. The collar may have come out the bearing housing. Remove the half round rings. Remove the stainless steel window guards from the bracket. Loosen the set screws on the seal sleeve to free the sleeve from the shaft. Loosen and remove the two nuts holding the seal gland to the pump.